This article which follows on the subject of How to Install a Bathtub Yourself is immensely compelling. You should take a peek.
Installing a bathtub isn't precisely brain surgery, yet it does need strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently obtainable, the job can move quickly; if you have to open a wall to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require a helper to leave the old tub and set in the brand-new one. Make certain you have qualified yourself for the task and also fit trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to take into consideration using one prior to you begin. Chances are you may require a professional plumber to make tube connections.
This write-up will certainly assist you set up a new bathtub in your washroom if you have actually already bought a brand-new bathtub as well as don't need to change the setup of your previous water pipes.
Your tools and also product checklist should consist of the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather problematic as a result of the restricted access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in area between the faucet as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous type must be connected to the tap finishes first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the bathtub until the spirit level reviews degree.
To mount taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system as well as inspect all joints as well as new pipework for leaks as well as tighten them if required. Fill the bathtub and also check the overflow outlet as well as the typical electrical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub needs to wait till the bathtub has been used at the very least when as this will certainly settle it into its final position.
Preparing for the Setup
First of all, the sustaining structure provided with the bathroom must be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its final placement.
Tiling Around the Bath tub
In the location where the bath fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall between the bathroom and the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your fixtures and also installations. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealant can crack rather early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that excerpt was beneficial. Enjoyed reading our posting? Please share it. Help somebody else check it out. I thank you for reading our article about How to Install a Bathtub Yourself.
Go Deal